#include "codetab.h"
#define LCD_SCL P1_2 //SCLK 时钟 D0（SCLK）
#define LCD_SDA P1_3 //SDA D1（MOSI） 数据
#define LCD_RST P1_7 //_RES hardware reset 复位
#define LCD_DC P0_0 //A0 H/L 命令数据选通端，H：数据，L:命令
#define XLevelL 0x00
#define XLevelH 0x10
#define XLevel ((XLevelH&0x0F)*16+XLevelL)
#define Max_Column 128
#define Max_Row 64
#define Brightness 0xCF
#define X_WIDTH 128
#define Y_WIDTH 64
void DelayMS(unsigned int msec)
{
unsigned int i,j;
for (i=0; i<msec; i++)
for (j=0; j<530; j++);
}
/*********************LCD 延时1ms************************************/
void LCD_DLY_ms(unsigned int ms)
{
unsigned int a;
while(ms)
{
a=1800;
while(a--);
ms--;
}
return;
}
/*********************LCD写数据************************************/
void LCD_WrDat(unsigned char dat)
{
unsigned char i=8, temp=0;
LCD_DC=1;
for(i=0;i<8;i++) //发送一个八位数据
{
LCD_SCL=0;
temp = dat&0x80;
if (temp == 0)
{
LCD_SDA = 0;
}
else
{
LCD_SDA = 1;
}
LCD_SCL=1;
dat<<=1;
}
}
/*********************LCD写命令************************************/
void LCD_WrCmd(unsigned char cmd)
{
unsigned char i=8, temp=0;
LCD_DC=0;
for(i=0;i<8;i++) //发送一个八位数据
{
LCD_SCL=0;
temp = cmd&0x80;
if (temp == 0)
{
LCD_SDA = 0;
}
else
{
LCD_SDA = 1;
}
LCD_SCL=1;
cmd<<=1;;
}
}
/*********************LCD 设置坐标************************************/
void LCD_Set_Pos(unsigned char x, unsigned char y)
{
LCD_WrCmd(0xb0+y);
LCD_WrCmd(((x&0xf0)>>4)|0x10);
LCD_WrCmd((x&0x0f)|0x01);
}
/*********************LCD全屏************************************/
void LCD_Fill(unsigned char bmp_dat)
{
unsigned char y,x;
for(y=0;y<8;y++)
{
LCD_WrCmd(0xb0+y);
LCD_WrCmd(0x01);
LCD_WrCmd(0x10);
for(x=0;x<X_WIDTH;x++)
LCD_WrDat(bmp_dat);
}
}
/*********************LCD复位************************************/
void LCD_CLS(void)
{
unsigned char y,x;
for(y=0;y<8;y++)
{
LCD_WrCmd(0xb0+y);
LCD_WrCmd(0x01);
LCD_WrCmd(0x10);
for(x=0;x<X_WIDTH;x++)
LCD_WrDat(0);
}
}
/*********************LCD初始化************************************/
void LCD_Init(void)
{
P0SEL &= 0xFE; //让P0.0为普通IO口，
P0DIR |= 0x01; //让P0.0为为输出
P1SEL &= 0x73; //让 P1.2 P1.3 P1.7为普通IO口
P1DIR |= 0x8C; //把 P1.2 P1.3 1.7设置为输出
LCD_SCL=1;
LCD_RST=0;
LCD_DLY_ms(50);
LCD_RST=1; //从上电到下面开始初始化要有足够的时间，即等待RC复位完毕
LCD_WrCmd(0xae);//--turn off oled panel
LCD_WrCmd(0x00);//---set low column address
LCD_WrCmd(0x10);//---set high column address
LCD_WrCmd(0x40);//--set start line address Set Mapping RAM Display Start Line (0x00~0x3F)
LCD_WrCmd(0x81);//--set contrast control register
LCD_WrCmd(0xcf); // Set SEG Output Current Brightness
LCD_WrCmd(0xa1);//--Set SEG/Column Mapping 0xa0左右反置 0xa1正常
LCD_WrCmd(0xc8);//Set COM/Row Scan Direction 0xc0上下反置 0xc8正常
LCD_WrCmd(0xa6);//--set normal display
LCD_WrCmd(0xa8);//--set multiplex ratio(1 to 64)
LCD_WrCmd(0x3f);//--1/64 duty
LCD_WrCmd(0xd3);//-set display offset Shift Mapping RAM Counter (0x00~0x3F)
LCD_WrCmd(0x00);//-not offset
LCD_WrCmd(0xd5);//--set display clock divide ratio/oscillator frequency
LCD_WrCmd(0x80);//--set divide ratio, Set Clock as 100 Frames/Sec
LCD_WrCmd(0xd9);//--set pre-charge period
LCD_WrCmd(0xf1);//Set Pre-Charge as 15 Clocks & Discharge as 1 Clock
LCD_WrCmd(0xda);//--set com pins hardware configuration
LCD_WrCmd(0x12);
LCD_WrCmd(0xdb);//--set vcomh
LCD_WrCmd(0x40);//Set VCOM Deselect Level
LCD_WrCmd(0x20);//-Set Page Addressing Mode (0x00/0x01/0x02)
LCD_WrCmd(0x02);//
LCD_WrCmd(0x8d);//--set Charge Pump enable/disable
LCD_WrCmd(0x14);//--set(0x10) disable
LCD_WrCmd(0xa4);// Disable Entire Display On (0xa4/0xa5)
LCD_WrCmd(0xa6);// Disable Inverse Display On (0xa6/a7)
LCD_WrCmd(0xaf);//--turn on oled panel
LCD_Fill(0xff); //初始清屏
LCD_Set_Pos(0,0);
}
/***************功能描述：显示6*8一组标准ASCII字符串 显示的坐标（x,y），y为页范围0～7****************/
void LCD_P6x8Str(unsigned char x, unsigned char y,unsigned char ch[])
{
unsigned char c=0,i=0,j=0;
while (ch[j]!='\0')
{
c =ch[j]-32;
if(x>126){x=0;y++;}
LCD_Set_Pos(x,y);
for(i=0;i<6;i++)
LCD_WrDat(F6x8[c][i]);
x+=6;
j++;
}
}
/*******************功能描述：显示8*16一组标准ASCII字符串 显示的坐标（x,y），y为页范围0～7****************/
void LCD_P8x16Str(unsigned char x, unsigned char y,unsigned char ch[])
{
unsigned char c=0,i=0,j=0;
while (ch[j]!='\0')
{
c =ch[j]-32;
if(x>120){x=0;y++;}
LCD_Set_Pos(x,y);
for(i=0;i<8;i++)
LCD_WrDat(F8X16[c*16+i]);
LCD_Set_Pos(x,y+1);
for(i=0;i<8;i++)
LCD_WrDat(F8X16[c*16+i+8]);
x+=8;
j++;
}
}
/*****************功能描述：显示16*16点阵 显示的坐标（x,y），y为页范围0～7****************************/
void LCD_P16x16Ch(unsigned char x, unsigned char y, unsigned char N)
{
unsigned char wm=0;
unsigned int adder=32*N; //
LCD_Set_Pos(x , y);
for(wm = 0;wm < 16;wm++) //
{
LCD_WrDat(F16x16[adder]);
adder += 1;
}
LCD_Set_Pos(x,y + 1);
for(wm = 0;wm < 16;wm++) //
{
LCD_WrDat(F16x16[adder]);
adder += 1;
}
}
/***********功能描述：显示显示BMP图片128×64起始点坐标(x,y),x的范围0～127，y为页的范围0～7*****************/
void Draw_BMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[])
{
unsigned int j=0;
unsigned char x,y;
if(y1%8==0) y=y1/8;
else y=y1/8+1;
for(y=y0;y<y1;y++)
{
LCD_Set_Pos(x0,y);
for(x=x0;x<x1;x++)
{
LCD_WrDat(BMP[j++]);
}
}
}